Skip to main content

Making The Drunken Cutting Board!


This is my first cutting board. An interesting pattern emerges from the flowing "S" shape and works really well with the high contrast of maple and walnut. 


I made a few changes from the original, but I would be remiss not to link to the post were I first saw this project back in 2009: http://lumberjocks.com/poroskywood/blog/10833


The process begins with two board that are the same thickness. In this case my lumber was 7/8 of an inch thick.

I then cut them to 9" in width and 14 inches in length. Both boards being the same dimensions is key to this project turning out. 

At this point the two boards are joined with double stick tape and taken over to the band saw

I just an "S" shape and repeated the process 5 times. I tried to make them similar but not precise. A free form cut is sorta of what gives this project it's charm! 


There were some tool marks from the band saw, I *lightly* sanded them off at the drum sander. What you don't want to do is change the shape of the curve and ruin the mating of the two pieces.


Next, you can alternate each piece and glue up the boards in with a cool wavy look.

After the glue dries pass it through the planer and get two parallel surfaces for joining together again with double stick tape.

This time I swapped out blades in my band saw in hopes of making the process better. The issue was that I caused some blade drift that made gaps in the pattern. I would stick in the future with the smaller 3/16 4tpi blade that I had on for the first cut.

Now, we alternate the boards again and glue up for a second time. Once dried you can sand them flat or use your thickness sander. I used the planer, but it can chip out some of the cross grain.

Now we glue up for a THIRD time. This makes for a nice heavy cutting board about 1 1/2 inches thick. 

For the finish I simply added a two coats of mineral oil, allow 12 hours of drying time in between!


Please like and share! 
YouTube Channel: https://www.youtube.com/user/kludge1977
Facebook: https://www.facebook.com/kludge1977
Twitter: https://twitter.com/kludge1977
Pinterest: http://www.pinterest.com/kludge77

Comments

Popular posts from this blog

Book Tablet Holder

Tablet stand made from a 400 page book and some epoxy resin. Paper micarta is the proper term for it, but it doesn't really capture the essence of the idea. Those 400 pages hold but a single story, and now they can upright a device capable of holding thousands of stories. And with only a book and 30 some odd ounces of epoxy, you can make your own! Just don't use a book that is one of your favorites. Which  honestly is why I picked this one, and the fact that the name was well suited! Really it's the ultimate upcycling!

Rikon Mini Lathe

I got busy this weekend and completed a couple of projects. I took a number of pictures of my new lathe in action. Most of them during the turning of a recent euro stlye pen made from padauk and ebony with a CA finish. It was a SF Giants theme, and the lathe was covered with padauk streamers and ebony dust. Very cool first project. I had a little trouble with the finish owning to the extreme cold in the garage, but overall a pretty good result. As I normally do, I forgot something. I forgot to bring in the camera and upload the pictures to photobucket so I could post them. As such, there is once again no proof. sigh... Everything is simpler. No more wrench to move the tool rest or tail stock. No more indexing pin to take off the faceplate. No more hassle removing the centers or mandrels. Man what a difference! In addition I tried turning a few things between centers. Basically just mangled some spindle blanks. Good fun, lots of walnut shavings. So, the new lathe has officially been br...

Turning A Sphere

Turning a ball is more work than you think. I first tried a simple method.. Turn a blank round Form the ball Part off and sand. Clearly, not a ball... On to step two! Chuck up a chunk of walnut, and scrape out a cup... Part off for the tailstock.... Scrape out an matched set for the chuck side.. They should match up. Insert square block.. Okay. You turn off the edges, rotate your block. Turn off more edges, rotate your block. Etc. About 15-20 minutes later... You can see how I turned a way the jam chuck as I went. The closer you get to spherical, the less you remove each rotation. Like anything practice till you're happy with it!