Skip to main content

Starting Over

There are few things as defeating as starting over. When you believe that you have completed a project, paper, blog or task to realized that something is not satisfactory. You sit there putting the finishing touches on it when it hits you like a ton of bricks. You begin to rationalize. It's not that bad, I can fix it. No matter how hard you try, you know the truth of it cannot be escaped. Life is about to teach you a valuable lesson that you will shell out for in heaps of wasted time. Buckle up.

So you just finished the most amazing wrapping job on Earth. Perfectly folded corners and the most delightful bow you've ever tied. I mean, honestly, when does curling ribbon ever curl that well? Only when curling ribbon knows what you don't. It knows that you've been a total stooge and left the "HALF-OFF CLEARANCE" sticker smack dab in the center of Aunt Betsy's gift.

I recently found myself at the end of a woodworking project. It wasn't anything horribly involved, but in my mind it was nearly complete. It took me about 10 hours or so to get to this point, and this point wasn't pretty. No sir. My design, with two floating shelves, looked great on paper, but as paper doesn't have to worry about real world physics, it can't be blamed for failing to support itself in real life. Turns out I should have known better. Well, I do now...

As I stood there staring at it, I knew I what I was going to have to do. I didn't want to. I was getting down on all fours looking at it from weird angles. "Well that looks fairly good." I wanted to bust out the duct tape and bailing wire. Have you ever been there? Pretending you can fix a broken levy with a bucket of paint? You begin reasoning with yourself.

"Well, when you kinda close one eye, and tilt your head to the left...it's really not that bad."

"Are we talking about the same cabinet? I'm looking at the one that's shaped like a 'V'. Where's the one your blathering on about?"

"Is it really that far off?"

"You could check it for square, if you'd like a good laugh...."

"-sigh-. I'm going to have to start over from scratch."

"No doubt! You might want to even burn your old plans, just to be on the safe side. Better brew another pot of coffee."

I knew I was going to have to start over and re-design it from the bottom up. So I just bit the bullet and dismantled the entire thing. In the end, I'm glad I did, it turned out much better, and much more stable. I'm nearly done again. And this time, it looks like it's suppose to. Sometimes starting over, is just a simple fact of life. That being said, if I find some major flaw that I've overlooked... you can bet I'll be reaching for my can of paint!

Comments

Popular posts from this blog

Book Tablet Holder

Tablet stand made from a 400 page book and some epoxy resin. Paper micarta is the proper term for it, but it doesn't really capture the essence of the idea. Those 400 pages hold but a single story, and now they can upright a device capable of holding thousands of stories. And with only a book and 30 some odd ounces of epoxy, you can make your own! Just don't use a book that is one of your favorites. Which  honestly is why I picked this one, and the fact that the name was well suited! Really it's the ultimate upcycling!

Rikon Mini Lathe

I got busy this weekend and completed a couple of projects. I took a number of pictures of my new lathe in action. Most of them during the turning of a recent euro stlye pen made from padauk and ebony with a CA finish. It was a SF Giants theme, and the lathe was covered with padauk streamers and ebony dust. Very cool first project. I had a little trouble with the finish owning to the extreme cold in the garage, but overall a pretty good result. As I normally do, I forgot something. I forgot to bring in the camera and upload the pictures to photobucket so I could post them. As such, there is once again no proof. sigh... Everything is simpler. No more wrench to move the tool rest or tail stock. No more indexing pin to take off the faceplate. No more hassle removing the centers or mandrels. Man what a difference! In addition I tried turning a few things between centers. Basically just mangled some spindle blanks. Good fun, lots of walnut shavings. So, the new lathe has officially been br...

Turning A Sphere

Turning a ball is more work than you think. I first tried a simple method.. Turn a blank round Form the ball Part off and sand. Clearly, not a ball... On to step two! Chuck up a chunk of walnut, and scrape out a cup... Part off for the tailstock.... Scrape out an matched set for the chuck side.. They should match up. Insert square block.. Okay. You turn off the edges, rotate your block. Turn off more edges, rotate your block. Etc. About 15-20 minutes later... You can see how I turned a way the jam chuck as I went. The closer you get to spherical, the less you remove each rotation. Like anything practice till you're happy with it!